Shop
- Minimum quantity should 4 of "Discover EVGC6A-A battery (suitable for replacing TROJAN T105 / T125)"
Showing 256–270 of 808 resultsSorted by latest
-
Castor systems with stainless steel forksCastor (without fork) 150×40 mm, 179065KN, load capacity up to 500 kg
Polyamide stainless steel wheels (KN series) are solid wheels that offer low rolling and rolling resistance but are quite noisy. For smooth floors and heavier loads. Operates over a wide temperature range from - 40° to +90°C. High abrasion resistance and long service life. Resistant to many chemicals.
-
For floor cleaning machinesDiscover EVGC6A-A battery (suitable for replacing TROJAN T105 / T125)
DISCOVER DRY CELL AGMs are deep cycle traction batteries adapted to real working conditions - i.e. they can be quickly recharged with a charger of the appropriate capacity, can „tolerate” partial recharges during the course of the day, can withstand high instantaneous loads, have a higher energy density than GEL batteries, withstand well outdoor conditions, can be permanently left connected to the charger, etc. Ideal for installation in new equipment or for replacement, e.g. TROJAN T105 or T125. Simply select the right charger algorithm and the Discover EVGC6A-A will work long and reliably.
Remark:
- Always make sure you use the correct charging algorithm. DISCOVER AGM battery is suitable for all classic AGM charging algorithms that have a balancing mode (recommended), and is also suitable for charging with constant current and constant voltage (up to 2.45V/cycle) chargers, but strictly not for starter AGM battery chargers. I.e. EXIDE, Sonnenchein GEL or DISCOVER GEL charging algorithms are suitable for them as they all have a balancing mode.
- If you have had to undercharge the battery during the day, we recommend that you leave the battery overnight after the work to recharge it fully, in order to fully compensate for the damage caused by undercharging (as a single undercharge can destroy between 3 and 6 cycles of the battery's lifetime, which in total is about 450 at a depth of discharge of 80%, or about 500 to 700 at a discharge depth of 70%).
- All the information you need on how to use AGM batteries correctly, click here:
-
Noblelift Q Series 2 - 5 tonne electric forkliftsNoblelift FE4P50Q: lifts 5 tonnes. up to 4800 mm, triple boom, with 76.8V412Ah lithium battery, with 150A charger, full cab with heater, EU Pack, push with positioner
- Lifting capacity - 5000kg@500 mm for centre of gravity
- Lifting height 4800 mm, triple boom with 1268 mm free travel
- Building height - 2345mm
- Lateral fork advance and positioner
- Hydraulics control - mechanical levers
- Driver presence detection (OPS, the forklift does not move unless the operator is sitting in the forklift)
- Battery - lithium iron phosphate, 76.8V412Ah (works down to -200C) and a 48V100A charger (fully charges the battery in ~2 hours). The battery has heating during charging
- Fork length 1220 mm, fork trolley load protection frame
- Non-stick elastic tyres
- Fully shock-absorbing and adjustable seat
- Comfort Package (Rear-facing grab handle with horn button, 2 side mirrors, USB socket, rubberised grab handles and the aforementioned fully shock absorbing and adjustable seat)
- Full cabin with heater
- Front and rear working lamps
- Electric power steering for the EU internal market
- Warranty - 12 months or 2000 moto hours
- Note: Photos are for illustrative purposes
-
Noblelift Q Series 2 - 5 tonne electric forklifts
Noblelift FE4P50Q: lifts 5 tonnes. up to 4800 mm, triple str., with 76,8V412Ah lithium battery, with 150A charger, full cab with heater, EU Pack, mini levers, push with positioner
- Lifting capacity - 5000kg@500 mm for centre of gravity
- Lifting height 4800 mm, triple boom with 1268 mm free travel
- Building height - 2345mm
- Lateral fork advance and positioner
- Hydraulics control via mini-levers
- Driver presence detection (OPS, the forklift does not move unless the operator is sitting in the forklift)
- Battery - lithium iron phosphate, 76.8V412Ah (works down to -200C) and a 48V100A charger (fully charges the battery in ~2 hours). The battery has heating during charging
- Fork length 1220 mm, fork trolley load protection frame
- Non-stick elastic tyres
- Fully shock-absorbing and adjustable seat
- Comfort Package (Rear-facing grab handle with horn button, 2 side mirrors, USB socket, rubberised grab handles and the aforementioned fully shock absorbing and adjustable seat)
- Full cabin with heater
- Front and rear working lamps
- Electric power steering for the EU internal market
- Warranty - 12 months or 2000 moto hours
- Note: Photos are for illustrative purposes
-
Mechanical pallet trucksZakrem RWU-2500 galvanised hydraulic pallet truck
- Galvanised both frame and hydraulic pump
- Additionally equipped with stainless steel bearings
- Polyamide non-stick wheels
- Ideal for use in areas with high hygiene requirements, such as the food and pharmaceutical industries, or simply to have a trolley that is significantly more resistant to corrosion
- Comfortable to work with a soft plastic handle
- Made in the EU
-
Good price
Warehouse, lifting, stacking and stretching equipmentOrder picker up to 5 mm high - OPH01 (AGM batteries)
The OPH01 is a compact and modern design multifunction order picker. It has a maximum working height of up to 5 metres and is suitable for both manual picking of packages and for maintenance work at height on buildings or installations. With a width of only 750 mm and a minimum height of only 1454 mm, this order picker can pass through the narrowest of corridors and fits easily into most modern lifts. Designed for continuous operation, it comes complete with long-life AGM batteries.
-
Good price
Batteries GEL, AGM, Pb and othersDiscover EVU1A-A (12V33Ah) battery
This model is widely used in floor cleaning machines, scissor carts etc.
DISCOVER DRY CELL AGMs are deep cycle traction batteries adapted to real working conditions - i.e. they can be quickly recharged with a charger of the appropriate capacity, can „tolerate” partial recharges during the course of the day, can withstand high instantaneous loads, have a higher energy density than GEL batteries, withstand well outdoor conditions, can be permanently left connected to the charger, etc. Ideal for installation in new machinery and for replacing batteries that have already been used up. Simply select the right charger algorithm and the Discover Discover EVU1A-A deep cycle AGM battery will provide long and reliable service.
Remark:
- Always make sure you use the correct charging algorithm. DISCOVER AGM battery is suitable for all classic AGM charging algorithms that have a balancing mode (recommended), and is also suitable for charging with constant current and constant voltage (up to 2.45V/cycle) chargers, but strictly not for starter AGM battery chargers. I.e. EXIDE, Sonnenchein GEL or DISCOVER GEL charging algorithms are suitable for them as they all have a balancing mode.
- If you have had to undercharge the battery during the day, we recommend that you leave the battery overnight after the work to recharge it fully - this will fully compensate for the damage caused by undercharging (as a single undercharge can destroy between 3 and 6 cycles of the battery's lifetime, which is about 450 cycles at a discharge depth of 80%, or about 500 to 700 at a discharge depth of 70%).
-
For floor cleaning machinesDiscover EVGT6A-AM battery (replaces TROJAN T145)
DISCOVER DRY CELL AGMs are deep cycle traction batteries adapted to real working conditions - i.e. they can be quickly recharged with a charger of the appropriate capacity, can „tolerate” partial recharges during the course of the day, can withstand high instantaneous loads, have a higher energy density than GEL batteries, withstand well outdoor conditions, can be permanently left connected to the charger, etc. Ideal for both installation in new equipment and replacement, e.g. TROJAN T145. Just select the right charger algorithm and Discover EVGT6A-A will work long and reliably.
Remark:
- Always make sure you use the correct charging algorithm. DISCOVER AGM battery is suitable for all classic AGM charging algorithms that have a balancing mode (recommended), and is also suitable for charging with constant current and constant voltage (up to 2.45V/cycle) chargers, but strictly not for starter AGM battery chargers. I.e. EXIDE, Sonnenchein GEL or DISCOVER GEL charging algorithms are suitable for them as they all have a balancing mode.
- If you have had to undercharge the battery during the day, we recommend that you leave the battery overnight after the work to recharge it fully - in this case the damage caused by undercharging is fully compensated for (as one undercharge can destroy between 3 and 6 battery life cycles, which together add up to about 450 cycles at a depth of discharge of 80%, or about 500 to 700 at a discharge depth of 70%).
-
KS and KN wheel systems with polyamide wheelsFixed fork wheel 125×38 mm, 120050, load up to 300 kg
The Wicke KN series is a range of castors and systems for standard loads. They are characterised by low resistance to movement, good mechanical properties, abrasion resistance, non-abrasion and resistance to many chemicals.
-
KS and KN wheel systems with polyamide wheelsFixed fork wheel 150×40 mm, 143226, load up to 400 kg
The Wicke KN series is a range of castors and systems for standard loads. They are characterised by low resistance to movement, good mechanical properties, abrasion resistance, non-abrasion and resistance to many chemicals.
-
KS and KN wheel systems with polyamide wheels
Fixed fork wheel 125×38 mm, 120051, load capacity up to 300 kg
The Wicke KN series is a range of castors and systems for standard loads. They are characterised by low resistance to movement, good mechanical properties, abrasion resistance, non-abrasion and resistance to many chemicals.
-
KS and KN wheel systems with polyamide wheelsSwivel castors (without brake) 2 each 250×58 mm, 155043, load capacity up to 3400 kg
Wicke KS Series - reinforced wheels and systems for heavier loads and more intensive work. Low resistance to movement, good mechanical properties, abrasion resistant, non-abrasive and resistant to many chemicals.
-
KS and KN wheel systems with polyamide wheelsFixed fork wheel 250×58 mm, 169428, load up to 1500 kg
Wicke KS Series - reinforced wheels and systems for heavier loads and more intensive work. Low resistance to movement, good mechanical properties, abrasion resistant, non-abrasive and resistant to many chemicals.
-
KS and KN wheel systems with polyamide wheelsSwivel castor with brake 250×58 mm, 169424, load capacity up to 1500 kg
Wicke KS Series - reinforced wheels and systems for heavier loads and more intensive work. Low resistance to movement, good mechanical properties, abrasion resistant, non-abrasive and resistant to many chemicals.
-
KS and KN wheel systems with polyamide wheelsSwivel castor (without brake) 250×58 mm, 169423, load up to 1500 kg
Wicke KS Series - reinforced wheels and systems for heavier loads and more intensive work. Low resistance to movement, good mechanical properties, abrasion resistant, non-abrasive and resistant to many chemicals.
